软土地区管幕群顶管施工地面沉降监测与分析

依托上海14号线桂桥路站管幕段实例工程,对管幕群顶管顶进施工过程地面沉降情况进行监测,分析群顶管施工对地面沉降的影响,在此过程中对本工程采用水土分算或合算进行讨论。根据顶进过程实际工况和监测数据,分析管幕群顶管施工影响地面的原因,提出相应控制措施。结果表明:①管幕群顶管施工引起最大地面沉降出现在始发井出加固区区域;②在本工程中采用水土合算计算正面土压力较为符合实际情况;③管幕群顶管施工过程中影响地面变形的因素主要包括前舱压力、顶进速度、洞门止水、管壁摩擦和同步注浆等方面。     

Field study of a retaining wall constructed with clay-filled soilbags

This paper presents a field study of constructing retaining walls using soilbags that are formed by filling the excavated clayey soils into woven bags (geosynthetics). The strength and deformation of the soilbags filled with clayey soils were studied via laboratory tests. A 100?m testing retaining wall was constructed with soilbags in a waterway project. The lateral deformation, the lateral pressures and the surface settlements of the testing retaining wall were monitored during construction and after 7 months operation. The results show that the soilbags can increase the strength of clayey soils. After 7 months of the completion, the lateral deformation and the surface settlement of the testing retaining wall tend to be stable with the maximum values of 29.4?cm and 19.2?cm, respectively. The lateral earth pressure on the front retaining structure could be positively reduced owing to the interlayer's friction of soilbags. Compared to the conventional gravity concrete retaining wall, about 38% construction cost was saved in the 100?m testing retaining wall.     

Design and calibration of a laminar soil box suitable for a low-capacity shake table using free-field tests on Ganga sand

The present study concentrates on design, commissioning and calibration of a uniaxial laminar soil box suitable for use on a low base-shear capacity shake table available at IIT Kanpur, India. The box is designed to simulate the behavior of soil deposits subjected to earthquake motions, with minimal boundary effects due to reflection of waves at the boundary. The 1.1 m × 1.6 m × 0.765 m box is comprised of a series of individual lamina supported independently on multiple roller bearings guided through a guide channel. The outer frame connected to the guide rods is designed in such as way that it can transfer the self weight of each lamina out of the shake table. A series of free-field tests are carried out on dry Ganga sand sample to calibrate the box. Dynamic response parameters, such as acceleration, displacement, stress-strain behavior, strain-dependant modulus and damping ratio of the sand at various depth are investigated. Large strain and subsequent increased inelasticity is observed towards the top of the sand bed. The experimental results are further compared with equivalent-linear SHAKE analysis and nonlinear finite element ground response analysis of the free-field soil using OpenSees for assessing the performance of the laminar box.     

蛋类礼盒包装结构的缓冲性能研究

目的研究蛋类礼盒包装结构的缓冲性能。方法以蛋类尺寸为基础,建立可发性聚乙烯(expandable polyethylene. EPE)缓冲单元结构和组合结构,进行静态仿真分析和实验验证,比较结构在形状、叠合层数、组合形式等参数变化时的载荷与位移。结果结构层数变化相同时,单元结构的极限载荷从143N增加到236 N,组合结构的极限载荷从224 N增加到476 N,均呈近线性增长。结论蛋类礼盒包装中,组合结构的承载能力优于单元结构,通过单元结构的组合,可满足不同蛋类的包装要求。     

吹氩流量对结晶器流场影响的插钉工业试验

 结晶器吹氩流量对流场分布有明显影响，因此明确吹氩流量对结晶器内流场分布的影响规律对提高铸坯质量有重要意义。通过插钉法工业试验研究了吹氩流量对结晶器内流场分布的影响，并且定量分析了液位波动的变化。结果表明，随着吹氩流量的增大，流场形态从双环流逐步转变为复杂流和单环流。结晶器内流场形态从双环流转变为复杂流和单环流的过程中，水口附近速度逐渐增大，液位逐渐升高，弯月面速度分布逐渐转变为从水口流向窄面，液位波动也相应增大。因此，生产过程中应选择合适的吹氩流量，避免产生复杂流和单环流，以提高铸坯质量。     

Quantifying the efficiency and biases of forest Saccharomyces sampling strategies

Saccharomyces yeasts are emerging as model organisms for ecology and evolution, and researchers need environmental Saccharomyces isolates to test ecological and evolutionary hypotheses. However, methods for isolating Saccharomyces from nature have not been standardized, and isolation methods may influence the genotypes and phenotypes of studied strains. We compared the effectiveness and potential biases of an established enrichment culturing method against a newly developed direct plating method for isolating forest floor Saccharomyces spp. In a European forest, enrichment culturing was both less successful at isolating Saccharomyces paradoxus per sample collected and less labour intensive per isolated S. paradoxus colony than direct isolation. The two methods sampled similar S. paradoxus diversity: The number of unique genotypes sampled (i.e., genotypic diversity) per S. paradoxus isolate and average growth rates of S. paradoxus isolates did not differ between the two methods, and growth rate variances (i.e., phenotypic diversity) only differed in one of three tested environments. However, enrichment culturing did detect rare Saccharomyces cerevisiae in the forest habitat and also found two S. paradoxus isolates with outlier phenotypes. Our results validate the historically common method of using enrichment culturing to isolate representative collections of environmental Saccharomyces. We recommend that researchers choose a Saccharomyces sampling method based on resources available for sampling and isolate screening. Researchers interested in discovering new Saccharomyces phenotypes or rare Saccharomyces species from natural environments may also have more success using enrichment culturing. We include step-by-step sampling protocols in the supplemental materials.     

基体稀释或基体匹配石墨炉原子吸收光谱法测定土壤样品中铅和镉

用石墨炉原子吸收光谱法测定土壤样品中Pb和Cd时,有时候直接按照方法标准GB/T 17141—1997操作,测定结果不能满足质控要求。研究结果表明,目标元素系列标准溶液中,分别含和不含土壤基体元素Na、Mg、Al、Si、Fe、Ca等元素混合成分时,校准曲线斜率明显不同。为减小基体效应的影响,基于文献调研和实验结果,对上述方法标准实验步骤进行了下列改进:(1)取相同体积实际样品消解液混合后,定量加入到用于建立校准曲线的系列标准溶液中,用于基体匹配;(2)对消解液进行适度稀释,仍采用标准溶液建立校准曲线。用4个土壤标样和土壤样品加标测定结果对改进后的方法进行了验证,结果表明,基体稀释法测定Pb的回收率范围分别为90.4%~114%;测定低含量Cd时,回收率范围为84.1%~125%。基体匹配法测定Pb和Cd的回收率范围分别为93.0%~105%和102%~119%,基本满足土壤样品中重金属回收率为80%~120%的质控要求。样品中痕量镉在测定下限附近时,应严格控制稀释倍数,或采用基体匹配法测定。改进后的操作步骤适合日常检测工作中大批量土壤样品中Pb和Cd的准确测定。     

电感耦合等离子体原子发射光谱法测定土壤中8种组分

为满足土地质量调查的需求,实现土壤中多组分的同时消解及准确测定,提高大批量样品的分析效率,建立了土壤样品经高压密闭消解后,采用电感耦合等离子体原子发射光谱法(ICP-AES)测定K₂O、Na₂O、CaO、MgO、Ba、Mn、Cu、Zn的方法。通过对消解体系、酸用量、消解温度等方面的考察,确定最佳实验条件;并对待测液中共存元素Al、Fe的干扰进行探讨,两者均不干扰测定。各组分校准曲线线性相关系数均大于0.999;检出限为0.01~10μg/g。实验方法用于测定土壤标准样品GBW07385、GBW07386、GBW07388中K₂O、Na₂O、CaO、MgO、Ba、Mn、Cu、Zn,测定结果的相对标准偏差(RSD,n=12)为1.1%~4.3%,相对误差RE为-4.0%~4.6%。采用实验方法对土壤实际样品中K₂O、Na₂O、CaO、MgO、Ba、Mn、Cu、Zn进行测定,结果的RSD(n=6)为1.2%~4.6%;并与地矿行业标准方法DZ/T 0279.2—2016测定结果进行比对,测得结果基本一致。     

InSb红外探测器芯片粘接工艺研究

基于InSb红外探测器的封装特点,采用正交试验法研究了芯片粘接过程中基板平整度、粘接剂抽真空时间、配胶时间、固化条件等工艺参数对芯片性能及可靠性的影响。通过计算极差和方差分析了各因素对芯片可靠性的影响大小。结果表明,固化条件对粘接后芯片的性能影响最大,其次是配胶时间,而抽真空时间和基板平整度影响相对较小。针对极差分析得出的较优参数组合和较差参数组合,利用X射线衍射(XRD)研究了不同参数组合对晶片粘接的应力大小,所得结果与正交试验一致。     

Maximum dry density test to quantify pumice content in natural soils

Crushable volcanic soils are well-known for their distinctive texture, vesicular nature and grain fragility. These features of volcanic soils lead to difficulty in interpreting the results of laboratory and field testing because of the occurrence of particle crushing. Sands containing pumice particles are commonly found in the Hamilton Basin in the North Island of New Zealand. The pumice particles originated from a series of volcanic eruptions centered in the Taupo and Rotorua regions. As a result of flooding and erosion along the Waikato River, the pumice particles have become mixed with other materials and have been distributed over the Hamilton Basin; these mixtures are referred to herein as natural pumiceous (NP) sands. This paper initially investigates an appropriate technique for measuring the maximum dry density (MDD) of NP sands; then a modified MDD test is proposed for estimating the pumice contents of these sands. In order to examine the applicability of different standard methods for determining MDD, New Zealand and Japanese standards are employed. The results using the Japanese standard show consistent MDD values when repeating the tests due to negligible particle crushing. On the other hand, the results of MDD tests according to the New Zealand standard indicate that a significant amount of particle crushing occurs after each repeated test and, consequently, it is not possible to get the same result when the test is repeated. NP sands reach their ultimate potential breakage during the modified MDD tests (at least, for the level of loading applied) and they experience different levels of particle crushing which may be a function of their pumice content. As a way forward, the relative breakages of the materials tested are used to estimate the pumice contents of the NP sands.